Hello everyone, many friends still don't understand what the connecting rod of a car is for. But it doesn't matter, because today I will share with you some knowledge about when the car connecting rod needs to be replaced. I believe it can solve some of your confusion and questions. If it happens to solve your problem, I hope you can pay attention to this website. I hope it can help you!

When does the car connecting rod need to be replaced?

The car connecting rod needs to be replaced only when it is deformed or damaged, which leads to the failure of lateral stability function. When the vehicle turns, the inclination angle will increase. In extreme cases, it may overturn. If the rod is damaged and in a free state, when the vehicle turns, the stabilizer bar may hit other parts of the car, causing damage to the car or injury to people. If it gets stuck on the ground, it is easy to cause the vehicle to collide, etc.

The balance rod of the car's chassis enhances the balance and stability. It is designed to be installed in the middle part of the chassis, mainly to strengthen the overall rigidity of the chassis. Depending on the different factory design and chassis structure, some are omitted and replaced by other structures.

The functions of the car connecting rod

It has the functions of anti-tilting and stability. When the car turns or encounters bumpy roads, the force on both sides of the wheels is different. The car will transfer its center of gravity, causing the outer wheel to bear more pressure than the inner wheel. When one side bears more force, the gravity pushes the body down, which may cause a loss of control.

The function of the balance rod is to keep the forces on both sides within a small range, transfer the force from the outside to the inside, and let the inside bear some of the pressure, so that the balance of the body can be effectively controlled. If the balance rod is damaged, it may cause tilting during steering, which is relatively dangerous.

The balance link connecting rod on the rear shock tower is designed to be installed on the top of the rear shock tower. Its main function is to enhance the strength of the rear trunk, reduce the lateral torsion caused by centrifugal force, reduce the inclination degree of the rear of the vehicle when turning, and improve the cornering performance of the vehicle. The rear axle suspension enhanced balance link rod is designed to be installed in the connection position between the rear axle and the rear of the chassis. Its main function is to strengthen the connection between the rear axle and the chassis.

Why is the rotor connected to the top balance rod of the remote control airplane not rotating?

1. The propeller does not rotate is generally caused by the disconnection or soldering of the battery connection circuit. Please check the circuit...!

2. If the motor can rotate, but the upper wing does not move, it may be that the connection between the large gear and the center shaft slips. Solution: Tighten the screw or remove it to clean the oil, and then apply a little 502....!

Hope the above experience can help you...!

What are the consequences of a broken front stabilizer bar connecting rod for a car?

The consequences of a broken front stabilizer bar connecting rod for a car:

(1) It leads to the failure of lateral stability function, and the vehicle turns in the direction;

(2) The tilt angle of the turn will increase, and in extreme cases, it may cause overturning of the vehicle;

(3) If the rod is damaged and in a free state, when the vehicle turns in the direction, the stabilizer bar may hit other parts of the car, causing damage to the car or injury to people, and if it gets stuck on the ground, it is easy to cause the vehicle to collide, etc.

The function of the balance connecting rod on the car:

(1) It has the functions of anti-tilting and stability. When the car turns or encounters bumpy roads, the force on both sides of the wheels is different. The car will transfer its center of gravity, causing the outer wheel to bear more pressure than the inner wheel. When one side bears more force, the gravity pushes the body down, which may cause a loss of control.

(2) The function of the balance rod is to keep the forces on both sides within a small range, transfer the force from the outside to the inside, and let the inside bear some of the pressure, so that the balance of the body can be effectively controlled. If the balance rod is damaged, it may cause tilting during steering, which is relatively dangerous.

Well, this article ends here. If it can help you, I hope you can pay attention to this website!